5

You are shopping Northern Brewer US shopping site, to view our Canadian shopping site - Click Here

Hullwrecker™ 2-roller Grain Mill & Base

SKU# 42338

Standard Shipping Rates Apply to this product
For perfectly milled grains, ease of use and superior dependability, look no further than the Hullwrecker™ grain mill. Our new two roller mill takes the guess work out of achieving the ideal crush for your brewery.
Total:
$149.99

Availability: Out of stock

Hullwrecker™ 2-roller Grain Mill & Base

More Views

  • Hullwrecker™ 2-roller Grain Mill & Base
  • Hullwrecker™ 2-roller Grain Mill & Base
  • Hullwrecker™ 2-roller Grain Mill & Base
Product Details
For perfectly milled grains, ease of use and superior dependability, look no further than the Hullwrecker™ grain mill. Our new two roller mill takes the guess work out of achieving the ideal crush for your brewery. The Hullwrecker™ grain mill features a fully adjustable roller gap from 0.025” all the way to 0.1”, allowing you to finely tune the crush to your extract preference. Features included sealed bearing (not bushings!), a 7 Ib capacity grain hopper, an ergonomic crank handle, and unlike other available grain mills, the Hullwrecker™ comes complete with a custom designed metal base that fits perfectly on any standard 5 or 6.5 gallon plastic bucket.

Features:
  • Sealed ball bearings
  • Ergonomic crank handle
  • 7 Ib capacity grain hopper
  • Included heavy duty metal base, fits on standard 5 or 6.5 gallon plastic buckets
  • Use with included crank handle, or electric drill
Additional Information
Reviews
4.0 / 5.0
2 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
1
0
1
0
0
Awesome Mill
This is a great mill, it went together with ease and looks great. I love the bucket plate, I uasally use a drill to run the mill but I milled one batch of grain with the crank handle just to see how well it worked. The crank is a bit slow, as with any mill, but works very smooth and even. The crank has a Phillips Head screw to hold it in place and its difficult to get it tight enough to keep it from slipping, it really should be a hex head bolt. The mill shafts are supported by sealed bearings instead of bronze bushings, the bronze bushings wear over time and the shafts get sloppy. This is my second mill and highly recommend this to anyone milling there own grain.
December 10, 2017
Purchased
3 weeks ago
Not bad, could be improved
This is my first grain mill, so I don't have anything else to compare to the Hullwrecker. This mill requires a little bit of assembly which is kind of tedious with all the tiny screws and locking nuts to assemble the hopper. My fingers had trouble with the screws, especially as they are so close to the inside corners. The rest of it goes together very easily. My biggest gripe is the way the handle attaches to the main shaft. There's only a screw to hold it in place and it must be tightened with a lot of force, but even then you cannot grind anything towards the finer end of the setting. The handle just spins around. The shaft should have been designed with a flat edge or two opposite flat edges that the handle can lock onto. I wanted my rollers set to the width of a credit card for my BIAB brewing, but the handle spins when set that low. I have to start with a larger gap setting, then run my grain through again with a smaller setting. Causes more work. If the shaft design was better this would be an awesome mill, but I think I'm going to be fighting with that handle slipping.
December 3, 2017
Purchased
2 weeks ago
Q&A
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 1 answer
Will this grain mill allow the use of a power drill in lieu of the hand crank?
A shopper on Dec 9, 2017
BEST ANSWER: Yes, the hand crank is removable.

You may also be interested in:

Please wait...

Your selected product has been added to your Cart.
Continue shopping
View cart & checkout