Faucet Adapter

SKU: 7233

This faucet adapter for bottle washers.

Male Faucet Fitting = 15/16" Straight Threads with 27 TPI (Threads Per Inch)
Female Faucet Fitting = 27/32" Straight Threads with 27 TPI
Garden Hose Fitting = 17/16" Straight Threads with 11.5 TPI

Availability: In stock


Faucet Adapter


Faucet adapter for bottle washers. Can also be used to attach Standard Chiller with vinyl tubing (#7869) to a threaded kitchen sink faucet.

Additional Information

Support Documents: N/A

Customer Reviews

Works and Sticks Review by Rich
This piece seems to fit well without leaks for most, myself included, but it does tend to get stuck to the faucet and can be difficult to remove. I needed pliers to remove it from the faucet each time, and the fourth time I tried to remove it - it broke. Be very cautious if you end up resorting to using pliers. Not bad for $5 however. (Posted on 4/7/15)
Worked as designed Review by David
I bought this for my plate chiller. I used thread seal tape from Ace Hardware, tightly secured it with pliers and it worked perfect. No leaks. (Posted on 11/25/14)
Works well on most faucets Review by Felix
The adapter works well on most faucets. My kitchen faucet unfortunately does not have enough thread exposed to get a good seal -- sprayed all over my walls several times. Works great in the bathroom however.

Not giving it 5 stars because it is hard to remove from the faucet at times -- it would be nice if it was a bit longer and provided some surface to apply a wrench or pliers to remove it. (Posted on 12/4/13)
What I needed. Review by Daniel
Works well, but gets stuck on the faucet. A must for all wort chillers. (Posted on 11/19/13)
Works as intended Review by Daniel
Once I moved, I no longer had a slop sink to hook my wort chiller to. This connection fits perfectly into the kitchen sink. (Posted on 11/13/13)
Essential Review by Michael
Very useful for running water through my wort chiller from the kitchen faucet. (Posted on 7/12/13)
Might work for you, might not Review by Joshua
Did not work for me. Same issue as several others. Just not enough turns and it would not screw down and hold a seal.

After a bit of trial and error and a few trips to the home improvement store I found that my faucet has a thread size of 55/64.

(Posted on 7/5/12)
Works great Review by William
Don't have any issue with it, works as it states.
Now I can use a bottle washer and a wort chiller.
I have the threads on the outside of my faucet. (Posted on 6/15/12)
Just what I needed Review by Ryan
This thing worked perfect for me; easy installation and good seal. (Posted on 12/5/11)
Inside fine threads cut to large Review by Matt
Won't fit my sink, my faucet threads are also too small. The inside threads on the adapter. (Posted on 10/20/11)
slips off faucet Review by rr
bought new faucet to use this and it still slips off threads (Posted on 10/12/11)
No good Review by Thefirebuilds
Won't fit my sink, my faucet threads are too small. Will have to see what hardware hank can do for me. (Posted on 9/3/11)
worked great for me on three different faucets so far Review by hexmonkey
Worked great for me on every faucet I've tried it on.

However, I suspect that NB should make a note on this item that says ONE SIZE FITS MOST. My on-the-faucet water filter in my kitchen came with no less than five different threaded adapters to fit every permutation of faucet out there. (Posted on 4/11/11)
Not enough fine threads Review by GreenTeaBreath
Got this to use with the Jet Bottle Washer (which is awesome). My slop sink has a nicer spigot and fine threads. This looks like it has fine threads, which it does. But, between the two, there are just not enough turns. So, although this was able to screw in, the two didn't hold and is unusable. I ended up going to a plumbing supply store and picked up something there. This thing's cost doesn't justify the shipping to send back. (Posted on 1/12/11)