5

You are shopping Northern Brewer US shopping site, to view our Canadian shopping site - Click Here

Monster Mill Grain Mills

249.99

SKU# U40914

Standard Shipping Rates Apply to this product
Includes roller assembly, base, and steel hopper - just add a corded electric drill or a 3/8" crank handle for the utlimate in pre-mash gristing experience.
Available as a 2-roller mill or 3-roller mill. The 2 roller model is pictured.

Fields marked with (*) are required

There is an extra handling fee of 0 for the selected item(s).
Total:
$0.00

Availability: In stock

Monster Mill Packages - MM3 Pictured

More Views

  • Monster Mill Packages - MM3 Pictured
  • Monster Mill Packages - MM3 Pictured
Product Details

MM2 Package

A heavy-duty, fully-adjustable all-purpose mill for homebrewers of all levels and batch sizes. Includes roller assembly, base, and steel hopper with 11 lb. capacity - just use a corded electric drill or add a 3/8" crank handle for a consistently perfect crush every time.

The MM2 boasts a double-roller configuration, with an adjustable gap spacing between the two rollers - this means you can set the gap tighter or coarser to dial in your efficiency and custom tailor the crush to suit your system, sparging or steeping method, and malt from batch to batch.

Roller Assembly: 6061 aluminum block frame with two 6" long x 1.5" dia. knurled steel rollers riding on SAE 841 oil- impregnated bronze bushings adjustable roller gap spacing with 0-0.070" range dual eccentric gap spacing adjusters, built from stainless steel to prevent galling 3/8" integral drive shaft w/3 flats for drill driving or a hand crank, 2" long outside frame 3/8" integral axles average throughput 6 lbs/min.

Hopper: heavy duty galvanized steel 9" overall height 11.5" x 12.75" at the top 11 lb. capacity Base: approx. 12 x 12" to fit over standard 5 or 6 gallon buckets radiused top edges and corners hand-routed grist window

MM3 Package

This is the mill if you're brewing large batches, or want to maximize mash efficiency at any volume. Heavy-duty triple-roller homebrew mill is designed for motorization (can be powered with a corded electric drill) and features an average throughput of 8 lbs./minute and adjustable gap spacing for fine-tuning your crush.

Why three rollers?

The MM-3 crushes all your grain twice, with one pass through the mill. It starts with a preliminary crush through the initial fixed gap between the top two rollers, and then ends with a pass through the second gap between the drive roller, and the bottom third roller. The initial pass slightly flattens the grain, and gets it ready for the next crush, that breaks apart the grains and loosens the starch with minimal husk damage.

Includes roller assembly, base, and steel hopper with 11 lb. capacity - just add a corded electric drill or a 3/8" crank handle for the ultimate pre-mash gristing experience.

Roller Assembly: 6061 aluminum block frame with three 6" long x 1.5" dia. knurled steel rollers riding on SAE 841 oil- impregnated bronze bushings .060"fixed primary gap, 0-0.065" fully-adjustable secondary gap dual eccentric gap spacing adjusters, built from stainless steel to prevent galling 3/8" integral drive shaft w/3 flats for drill driving, 2" long outside frame 3/8" integral axles average throughput 8 lbs/min.

Hopper: heavy duty galvanized steel 9" overall height 11.5" x 12.75" at the top 11 lb. capacity Base: approx. 12 x 12" to fit over standard 5 or 6 gallon buckets radiused top edges and corners hand-routed grist window

Additional Information
Support Documents: No
Reviews
5.0 / 5.0
8 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
8
0
0
0
0
Well Made Mill
I'm very happy with the triple-roller mill. It gives a very efficient, complete crush while creating little dust. The husk is fully removed from the kernel. The key to this and other three-roller mills is that you will need a corded drill that is capable of generating high torque. Cheap drills will bind up and stop at speeds slow enough to feed grain into the rollers and turn way too fast to feed at high speeds. I use a 1/2" Hitachi drill rated at 9 amps and 650 in-lbs of torque. I just load up the mill and run the drill at relatively low speed. This gives great results.
November 7, 2015
Monster Mill 3 Roller provides a consistent, easy to dial in grist. A+
I will be honest, this thing came with no instructions and to a not so mechanically inclined guy like me this proved a little challenging. After finding some pictures of the assembled mill and getting very personalized service from the company, I can honestly say this thing provides a consistent, easy to dial in grist. A+
July 12, 2013
grate mill
the mill works perfect . but took a minute to look at all the parts and figure it out with no instructions but looking at the picture on this site it was really simple. the adjustment seemed minimal but makes a big difference in the crush. very impressed went from about 75% to 85+ efficiency with just this new mill, with the autosparge i'm hoping to get 90% or better mash efficiency
September 10, 2013
Excellent mill, solid value, great crush
I purchased the Monster Mill MM2 kit, which includes the mill itself, hopper, and base. Assembly was simple and quick. The base fits nicely atop a standard bucket. With a drill attached, milling grains is easy and fast. I haven't yet had any trouble with the mill losing the gap setting. Do yourself a favor and get a power drill, as well as a gap tool to measure the gap setting, and you're golden. Very satisfied.
May 10, 2015
MM3
Works great!
July 25, 2016
Love that thing
Lasts forever. My only complaint if I had to get picky would be to get the whole roller to adjust with a single knob rather than each side individually. But honestly, with a feeler gauge it takes about 45 seconds to adjust. Get or build the extensions from the beginning to do a full batch easily.
September 30, 2015
Best meal I have ever used. That's one
I love this mill. I do wish I had purchased the upgraded version though. The new version allows you to see your roller spacing without having to measure with every adjustment. But at least I know I will never have to purchase another mill. You will only be limited by the strength of the motor or drill that you attach it to.
December 13, 2016
Purchased
over 2 years ago
Cadillac of mills
Simply awesome.
Pro: Eats through grain with very little effort. Super big solid metal hopper. Hulls remain intact.
Con: The mill has to be gauged with the hopper off.
So happy my wife talked me into getting it.
Bench mounted and drill powered... on the lower speed setting of course.
Bench mounted and drill powered... on the lower speed setting of course.
May 30, 2017
Purchased
2 months ago
Q&A
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 2 questions Browse 2 questions and 4 answers
Could your unit roll oats for horses?? Which unit would you recommend?? Do not want to grind or crimp just roll flat ! Thank you
A shopper on Dec 13, 2016
BEST ANSWER: I would assume that this mill should be able to roll oats. With the three roller design you can set the first roller to start the pressing of the oat, and the second roller can do the rest of the job. I would actually think that it would depend more on the motor or drill that is attacked. The motor will probably have to have a little more torque and not worry about speed as much to assure the rollers grab properly.
Would the 3 roller do shelled corn?
M I on Dec 8, 2015
BEST ANSWER: Hello Michael,

Thank you for choosing Northern Brewer! I would not advise it, the mill is made for malted grains which are much softer and easier to crack. That corn will more than likely destroy the mill. I hope that this helps!

You may also be interested in:

Please wait...

Your selected product has been added to your Cart.
Continue shopping
View cart & checkout